270 lines
8.8 KiB
C
270 lines
8.8 KiB
C
|
#include <stdio.h>
|
||
|
#include <stdlib.h>
|
||
|
#include <stdint.h>
|
||
|
#include <stdbool.h>
|
||
|
|
||
|
#include <TM4C123GH6PM.h> // The Header File for EK-TM4C123GXL LaunchPad
|
||
|
// #include <TM4C1294NCPDT.h> // The Header File for EK-TM4C1294XL LaunchPad
|
||
|
#include "ez123G.h"
|
||
|
#include "MyDefines.h" // Your Definitions for the System Configuration
|
||
|
|
||
|
#define _TIMER_CFG_1632B_TIMER16B (0x4)
|
||
|
#define _TIMERA_CAPTURE_EVENT_INT_CLR (1 << 2)
|
||
|
#define _TIMERA_CAPTURE_EVENT_INT (1 << 2)
|
||
|
#define _TIMERB_CAPTURE_EVENT_INT_CLR (1 << 10)
|
||
|
#define _TIMERB_CAPTURE_EVENT_INT (1 << 10)
|
||
|
|
||
|
float SYSTEM_CLOCK_FREQ = ________;
|
||
|
|
||
|
typedef enum EDGE_EVENT{
|
||
|
FALLING_EDGE,
|
||
|
RISING_EDGE
|
||
|
|
||
|
} EDGE_EVENT;
|
||
|
|
||
|
void Setup_PWM(void);
|
||
|
void Setup_Timer(void);
|
||
|
void Setup_GPIO(void);
|
||
|
void Setup_UART(void);
|
||
|
|
||
|
uint32_t MeasurePeriod(void);
|
||
|
uint32_t MeasurePulseWidth(void);
|
||
|
void UART_PrintString(char * s);
|
||
|
|
||
|
typedef struct PWM_CONTROL{
|
||
|
uint16_t load;
|
||
|
uint16_t cmp;
|
||
|
} PWM_CONTROL;
|
||
|
|
||
|
PWM_CONTROL Pwm[]={
|
||
|
{18150, 4628},
|
||
|
{6665, 3032},
|
||
|
{12490, 8118},
|
||
|
{49996, 37497},
|
||
|
{8328, 2914}
|
||
|
};
|
||
|
|
||
|
// On-board switch
|
||
|
uint32_t *Sw = (uint32_t *) (((char*)_____)+ (______ << 2));
|
||
|
|
||
|
int main()
|
||
|
{
|
||
|
PEZOBJ_LCD lcd;
|
||
|
volatile uint32_t T;
|
||
|
volatile uint32_t t;
|
||
|
uint32_t freq;
|
||
|
double duty;
|
||
|
char str[100];
|
||
|
int idx = 0;
|
||
|
uint8_t i = 0;
|
||
|
bool preSw = true;
|
||
|
uint16_t currSw;
|
||
|
|
||
|
Setup_123G_80MHz(); // Setup System Clock to 80 MHz
|
||
|
|
||
|
Setup_PWM();
|
||
|
Setup_Timer();
|
||
|
Setup_GPIO();
|
||
|
|
||
|
lcd = ezLCD_Create();
|
||
|
ezLCD_Connect_DataPort(lcd, GPIO____, PIN_3_0);
|
||
|
ezLCD_Connect_ENPin(lcd, GPIO____, PIN7);
|
||
|
ezLCD_Connect_RSPin(lcd, GPIO____, PIN6);
|
||
|
ezLCD_Connect_RWPin(lcd, GPIO____, PIN4);
|
||
|
|
||
|
ezLCD_Start(lcd);
|
||
|
ezLCD_ClearDisplay(lcd);
|
||
|
|
||
|
PWM0->_1_CTL &= ~0x01; // Disable PWM Module 0, Generator 1
|
||
|
PWM1->_3_CTL &= ~0x01; // Disable PWM Module 1, Generator 3
|
||
|
PWM0->_1_LOAD = Pwm[idx].load;
|
||
|
PWM0->_1_CMPB = Pwm[idx].cmp;
|
||
|
PWM1->_3_LOAD = Pwm[idx].load;
|
||
|
PWM1->_3_CMPB = Pwm[idx].cmp;
|
||
|
PWM0->_1_CTL |= 0x01; // Disable PWM Module 0, Generator 1
|
||
|
PWM1->_3_CTL |= 0x01; // Disable PWM Module 1, Generator 3
|
||
|
|
||
|
while(1){
|
||
|
|
||
|
currSw = *Sw;
|
||
|
if (preSw && (!currSw)){
|
||
|
if (++idx >= (sizeof(Pwm) / sizeof(PWM_CONTROL))) idx = 0;
|
||
|
PWM0->_1_CTL &= ~0x01; // Disable PWM Module 0, Generator 1
|
||
|
PWM1->_3_CTL &= ~0x01; // Disable PWM Module 1, Generator 3
|
||
|
PWM0->_1_LOAD = Pwm[idx].load;
|
||
|
PWM0->_1_CMPB = Pwm[idx].cmp;
|
||
|
PWM1->_3_LOAD = Pwm[idx].load;
|
||
|
PWM1->_3_CMPB = Pwm[idx].cmp;
|
||
|
PWM0->_1_CTL |= 0x01; // Disable PWM Module 0, Generator 1
|
||
|
PWM1->_3_CTL |= 0x01; // Disable PWM Module 1, Generator 3
|
||
|
timer_waitMillis(100);
|
||
|
}
|
||
|
preSw = currSw;
|
||
|
|
||
|
T = MeasurePeriod();
|
||
|
t = MeasurePulseWidth();
|
||
|
freq = ____________ ;
|
||
|
duty = ____________ ;
|
||
|
sprintf(str, "%02d: f%d = %d Hz ", i, idx, freq);
|
||
|
ezLCD_Position(lcd, 0,0);
|
||
|
ezLCD_PrintString(lcd, str);
|
||
|
sprintf(str, "Duty = %.1f %% ", duty);
|
||
|
ezLCD_Position(lcd, 1,0);
|
||
|
ezLCD_PrintString(lcd, str);
|
||
|
i = (++i) % 100;
|
||
|
timer_waitMillis(500);
|
||
|
}
|
||
|
|
||
|
}
|
||
|
|
||
|
void Setup_PWM(void)
|
||
|
{
|
||
|
ENB
|
||
|
|
||
|
// 1. Enable Clock for PWM Module
|
||
|
SYSCTL->RCGCPWM |= (_______);
|
||
|
while((SYSCTL->PRPWM & (_______)) != (_______)){};
|
||
|
// 2. Enable and Setup Clock Divider for PWM
|
||
|
SYSCTL->RCC |= (1 << 20); // RCC[20]=1:USEPWMDIV
|
||
|
SYSCTL->RCC &= ~(0x07 << 17); // RCC[19:17]=000 PWMDIV
|
||
|
SYSCTL->RCC |= (________ << 17); // RCC[19:17]=0x04 divider=/32
|
||
|
// 3. Disable PWM Generator
|
||
|
// 4. Configure LOAD (Period), CMP (Initial Duty), GEN (PWM Mode) values
|
||
|
// 5. Enable PWM Generator
|
||
|
// 6. Enable PWM Output
|
||
|
|
||
|
}
|
||
|
void Setup_Timer(void)
|
||
|
{
|
||
|
// 1 . Enable Clock for TIMER
|
||
|
SYSCTL->RCGCTIMER |= ________;
|
||
|
while ((SYSCTL->PRTIMER & (________)) != (________)) {}
|
||
|
// 2. Disable TIMER
|
||
|
TIMER_->CTL &= ~(________);
|
||
|
// 3. Configure TIMER
|
||
|
TIMER_->CFG = _TIMER_CFG_1632B_TIMER16B;
|
||
|
// 4. Configure Timer n Mode: GPTMTAMR
|
||
|
TIMER_->TAMR = ________;
|
||
|
// 5. Configure Timer Event Mode
|
||
|
TIMER_->CTL &= ~________;
|
||
|
TIMER_->CTL |= ________;
|
||
|
// 6. Configure Load
|
||
|
TIMER_->TAILR = 0xffff; //0x00000000;
|
||
|
//Set the prescaler to 0xff
|
||
|
TIMER_->TAPR = 0xff;
|
||
|
TIMER_->ICR = _TIMERA_CAPTURE_EVENT_INT_CLR;
|
||
|
TIMER_->IMR = 0;
|
||
|
// 7. Enable GPTM Timer
|
||
|
TIMER_->CTL |= ________; // Enable Timer
|
||
|
|
||
|
}
|
||
|
void Setup_GPIO(void)
|
||
|
{
|
||
|
|
||
|
// GPIO Initialization and Configuration
|
||
|
// 1. Enable Clock to the GPIO Modules (SYSCTL->RCGCGPIO)
|
||
|
SYSCTL->RCGCGPIO |= (_______);
|
||
|
// allow time for clock to stabilize (SYSCTL->PRGPIO)
|
||
|
while((SYSCTL->PRGPIO & (_______)) != (_______)){};
|
||
|
// 2. Unlock PD7 and/or PF0 on TM4C123G (GPIO->LOCK and GPIO->CR)
|
||
|
//GPIOF->LOCK = 0x4C4F434B;
|
||
|
//GPIOF->CR |= _PIN0;
|
||
|
|
||
|
//GPIOD_AHB->LOCK = 0x4C4F434B;
|
||
|
//while( (GPIOD_AHB->LOCK & 0x01) == 0x01) {};
|
||
|
//*(((char*)GPIOD_AHB)+0x524) = 0xFF;
|
||
|
|
||
|
// 3. GPIO Analog Mode Select (GPIOAMSEL)
|
||
|
// 4. GPIO Port COntrol (GPIOPCTL)
|
||
|
// 5. Clear AFSEL bits to 0 to select regular I/O
|
||
|
// 6. GPIO Pin Direction (GPIODIR) 0 for input, 1 for output
|
||
|
// 7. Set PUR bits to 1 to enable internal pull-up resistor
|
||
|
// 8. Set DEN bits to 1 to enable data pins
|
||
|
|
||
|
}
|
||
|
|
||
|
uint32_t MeasurePeriod(void)
|
||
|
{
|
||
|
volatile uint32_t edge1;
|
||
|
volatile uint32_t edge2;
|
||
|
uint32_t load;
|
||
|
|
||
|
// **** Capture firstEgde i.e. rising edge ****
|
||
|
TIMER_->CTL &= ~(_TIMERA_ENABLE);
|
||
|
TIMER_->CTL &= ~(_TIMERA_EVENT);
|
||
|
TIMER_->CTL |= ________; // Capture on the falling- or rising- edgs
|
||
|
TIMER_->CTL |= _TIMERA_ENABLE;
|
||
|
|
||
|
//1. Clear GPTM Timer A Capture Mode Event by writing 1 to
|
||
|
// corresponding bit on GPTMICR (TIMER1->ICR) register (CnERIS bit)
|
||
|
TIMER_->ICR = _TIMERA_CAPTURE_EVENT_INT_CLR;
|
||
|
//2. Waiting for capture event by check the GPTM Raw Interrupt Status
|
||
|
// GPTMRIS (TIMER1->RIS) register
|
||
|
while ((TIMER_->RIS & _TIMERA_CAPTURE_EVENT_INT) != _TIMERA_CAPTURE_EVENT_INT) {};
|
||
|
//3. Read the capture value from GPTMTAR (TIMER1->TAR) register
|
||
|
edge1 = TIMER_->TAR;
|
||
|
|
||
|
// **** Capture secondEgde i.e. falling edge ****
|
||
|
//4. Clear GPTM Timer A Capture Mode Event by writing 1 to
|
||
|
// corresponding bit on GPTMICR (TIMER1->ICR) register
|
||
|
TIMER_->ICR = _TIMERA_CAPTURE_EVENT_INT_CLR;
|
||
|
|
||
|
//5. Waiting for capture falling edge event by check the GPTM Raw Interrupt Status
|
||
|
// GPTMRIS (TIMER1->RIS) register
|
||
|
while ((TIMER_->RIS & _TIMERA_CAPTURE_EVENT_INT) != _TIMERA_CAPTURE_EVENT_INT) {};
|
||
|
|
||
|
//6. Read the capture value from GPTMTAR (TIMERa->TAR) register
|
||
|
edge2 = TIMER_->TAR;
|
||
|
|
||
|
//7. Calculate deltaT = highEdge - lowEdge
|
||
|
// Note: the deltaT must large than zero, cannot be negative value
|
||
|
|
||
|
|
||
|
|
||
|
|
||
|
}
|
||
|
uint32_t MeasurePulseWidth(void)
|
||
|
{
|
||
|
uint32_t edge1;
|
||
|
uint32_t edge2;
|
||
|
static uint32_t load;
|
||
|
|
||
|
// **** Capture first Rising-Edge ****
|
||
|
TIMER_->CTL &= ~(_TIMERA_ENABLE);
|
||
|
TIMER_->CTL &= ~(_TIMERA_EVENT);
|
||
|
TIMER_->CTL |= ________; // Capture on the Rising-Edge
|
||
|
TIMER_->CTL |= _TIMERA_ENABLE;
|
||
|
|
||
|
//1. Clear GPTM Timer A Capture Mode Event by writing 1 to
|
||
|
// corresponding bit on GPTMICR (TIMER1->ICR) register
|
||
|
TIMER_->ICR = _TIMERA_CAPTURE_EVENT_INT_CLR;
|
||
|
//2. Waiting for capture event by check the GPTM Raw Interrupt Status
|
||
|
// GPTMRIS (TIMER1->RIS) register
|
||
|
while ((TIMER_->RIS & _TIMERA_CAPTURE_EVENT_INT) != _TIMERA_CAPTURE_EVENT_INT) {};
|
||
|
//3. Read the capture value from GPTMTAR (TIMER1->TAR) register
|
||
|
edge1 = TIMER_->TAR;
|
||
|
|
||
|
TIMER_->CTL &= ~(_TIMERA_EVENT);
|
||
|
TIMER_->CTL |= ________; // Capture on the Falling-Edge
|
||
|
|
||
|
|
||
|
// **** Capture second Egde i.e. falling edge ****
|
||
|
//4. Clear GPTM Timer A Capture Mode Event by writing 1 to
|
||
|
// corresponding bit on GPTMICR (TIMER1->ICR) register
|
||
|
TIMER_->ICR = _TIMERA_CAPTURE_EVENT_INT_CLR;
|
||
|
|
||
|
//5. Waiting for capture falling edge event by check the GPTM Raw Interrupt Status
|
||
|
// GPTMRIS (TIMER1->RIS) register
|
||
|
while ((TIMER_->RIS & _TIMERA_CAPTURE_EVENT_INT) != _TIMERA_CAPTURE_EVENT_INT) {};
|
||
|
|
||
|
//6. Read the capture value from GPTMTAR (TIMERa->TAR) register
|
||
|
edge2 = TIMER_->TAR;
|
||
|
|
||
|
//7. Calculate deltaT = highEdge - lowEdge
|
||
|
// Note: the deltaT must large than zero, cannot be negative value
|
||
|
|
||
|
|
||
|
|
||
|
}
|
||
|
|